The Institute of Circuit Technology
The ICT Journal is published quarterly and freely available online.
Subscribe below to receive notification of each new issue.
|
Welcome to the latest edition of our Journal. We have a wide range of informative and educational content. Via-in-pad requirements and techniques. Ultra thin gold as a surface finish. Heavy copper pcb fabrication. Laser induced electroless copper deposition. An up to date e-book "Modern PCBA Manufacturing". We report on the sad passing of Steve Lloyd in members news. Industry news covers a wide range of topics from our corporate members. Please feel free to forward this Journal to colleagues who may be interested. They can subscribe using the link above to receive future editions. |
||
| Go back to Contents |
|
Section 2 - Calendar of Events
Note: Registration is now open for the ICT Christmas Evening Seminar, 24th November 2026. Puckrup Hall, Tewkesbury. Free to members and non-members. Read more... |
|
| Dates | Details |
| 23-26th March 2026 | ICT Foundation Course - Chester University |
| 14th April 2026 | ICT Evening Seminar - Meriden. Read more... |
| 9-10th Jun 2026 | EIPC Summer Conference |
| 6th Oct 2026 | ICT Annual Symposium and Fab Group Meeting. Read more... |
| 10-13th Nov 2026 | Electronica - Munich |
| 24th Nov 2026 | ICT Christmas Evening Seminar, Council Meeting and Fab Group Meeting. Puckrup Hall, Tewkesbury. Read more... |
| Feb 2 - 3rd 2027 | EIPC Winter Conference, Bremen, Germany. |
| April 3 - 8th 2027 | IPC Apex Expo, Anaheim Convention Center. |
| April 13 - 16th 2027 | ICT Foundation Course, Chester. |
| Go back to Contents | |
![]() As BGA and QFN pitches continue to shrink, the conventional arrangement in which the component pad, connecting trace and via occupy separate locations no longer provides enough routing space for some high-density PCB designs. Via-in-pad places the via directly within the component pad, saving space but also making a structure originally intended only for interlayer connection part of the soldering interface. This article first explains why via-in-pad is needed, then compares open vias, solder mask plugging, resin filling, conductive filling, copper electrofilling and Via in Pad Plated Over (VIPPO). It concludes with the key manufacturing controls and acceptance criteria for VIPPO based on IPC-4761 and IPC-6012F. The central point is simple: where a flat, continuous and solderable via-in-pad surface is required, merely closing the hole is not enough. The filling material, planarisation, copper-cap integrity and acceptance requirements must all be defined. 1. Why Via in Pad Is Needed In a conventional layout, the component pad provides the soldering surface, the via connects to the opposite side or internal layers, and the two are joined by a trace. This arrangement is simple, economical and comparatively easy to manufacture and inspect, including in Quick-Turn PCB Manufacturing projects. As pin counts increase and BGA and QFN pitches decrease, the spaces between pads may no longer provide enough room for both traces and vias. Designers may therefore place the via directly within the component pad. The pad, interconnection path and via then share one location instead of three separate areas, reducing fan-out space and opening additional routing channels. In some designs, this can also shorten high-speed signal or power paths, while multiple conductive vias may improve heat transfer from the component.
2. Assembly Risks of an Open Via in Pad Via-in-pad makes one location perform two functions: soldering and interlayer connection. If the via remains open, molten solder may wick down the plated hole wall during reflow, reducing the solder volume on the pad or making it inconsistent from one joint to another. • Insufficient solder in BGA balls or QFN joints; For a via-in-pad surface that must form a reliable solder joint, the manufacturing objective is therefore not merely to close the hole. It is to achieve stable internal filling, sufficient surface flatness and a continuous solderable metal surface. However, not every via-in-pad requires VIPPO. An open via may be acceptable in a large thermal pad when the design, stencil aperture, via dimensions and assembly process have been evaluated accordingly. Filling, planarisation and copper capping become the more reliable choice when the via location must provide a stable, flat and continuous solderable surface. 3. Via in Pad Treatment Methods and Their Tradeoffs Different via treatments serve different purposes. If design data states only “plugged via” or “filled via” without defining the material, planarisation and copper-cap requirements; the designer and manufacturer may have very different interpretations of the intended finished structure. Table 1. Via Filling Options Open via: The via opening remains exposed Simplest process and lowest cost Solder may drain into the hole; unsuitable where consistent solder volume is required. Solder mask plugging: Solder mask closes or partially fills the via Economical for some ordinary vias Not a structural fill; cannot reliably create a flat, continuous solderable surface. Resin filling and planarisation: Specialised resin is filled, cured and ground flat Stable internal support and improved flatness Without a continuous copper cap, it is not necessarily a complete solderable via-in-pad. VIPPO Resin filling, planarisation and copper cap plating: Flat, continuous solderable surface suitable for BGA and QFN More process steps and cost; fill, grinding and cap plating require close control. Conductive material filling: Conductive paste or resin fills the via Can improve selected thermal or electrical characteristics Conductivity is not equivalent to solid copper; material compatibility and thermal reliability require evaluation. Copper Electrofill: Copper plating completely fills the hole Good electrical and thermal performance for suitable HDI structures Higher equipment and process demands; limited by hole geometry and aspect ratio.
Solder mask plugging is not unsuitable in every application. For ordinary vias, it remains a common and economical process when the objective is to reduce solder entry, solder balls or flux residues. However, solder mask is primarily intended to protect circuitry, reduce copper oxidation, define solderable areas and prevent solder bridging. It is not designed as a structural filling material that will be planarised and plated over. In a solderable via-in-pad, curing shrinkage, incomplete filling, surface recession and gas release during thermal processing can all affect assembly. Solder mask plugging should therefore not be treated as an alternative to VIPPO. The Relationship Between Resin Filling Planarisation and Copper Capping Resin filling provides internal support and closes the hole. Planarisation removes the height difference at the opening. Copper cap plating creates surface continuity and solderability. Each step performs a different function; completing only one does not produce a complete solderable via-in-pad structure. Conductive Filling and Copper Electrofill Conductive paste or conductive resin may be used in selected structures to improve thermal or electrical performance, but its conductivity should not be assumed to equal solid copper. Material expansion, compatibility and fill integrity must still be controlled. Copper electrofill is more commonly associated with laser microvias and stacked structures in advanced Multilayer PCB Manufacturing. It can provide an excellent electrical and thermal path, but places stricter demands on via diameter, depth, aspect ratio and plating uniformity. Conductive material filling, copper electrofill and resin-filled VIPPO are not interchangeable without engineering evaluation. 4. VIPPO Manufacturing Process and Key Controls VIPPO means Via-in-Pad Plated Over. In the IPC-4761 classification of via protection structures, a via that is filled and then metallised over the opening is generally described as a Type VII filled and capped via. A typical simplified process is: drilling → hole-wall metallisation → cleaning and drying → resin filling → curing → planarisation → copper cap plating → final surface finish. Individual manufacturers may adjust the detailed sequence around circuit formation, copper plating and final finishing. Where the finished structure must support demanding service conditions, these controls should form part of the broader High-Reliability PCB manufacturing requirements.
Hole-wall metallisation: The via must first have a reliable plated copper wall to provide the interlayer electrical connection. 5. How VIPPO Should Be Accepted VIPPO acceptance should not stop at confirming that the via appears to be filled. Inspection should cover copper-cap thickness, protrusion and depression, cap continuity, exposure of filling material and the precise interface at which any separation occurs. Copper Cap Thickness Protrusion and Depression According to IPC-6012F Section 3.6.2.11.2 and Table 3-13, vias filled with resin or another specified material and then copper capped are subject to the applicable requirements for copper-cap thickness, protrusion and depression. Table 2.
Copper Cap Voids and Exposure of Filling Material For a solderable component pad, a void in the copper cap that exposes the internal filling material is not acceptable. The standard provides an exception for areas covered by solder mask, but that is not the normal condition for a solderable via-in-pad surface. Location of Separation When separation is observed, the exact interface matters. Separation between the copper cap and the filling material may be acceptable, provided that the copper cap remains continuous and intact and still satisfies the specified thickness, protrusion and depression limits. Separation between the cap plating and the underlying copper plating is not acceptable because it disrupts the copper-to-copper structural interface. Inspection Methods and Procurement Documentation These features are commonly verified by visual inspection, surface-profile measurement and microsection analysis. Procurement documentation should identify the applicable standard revision, product class, filling material, Type VII or VIPPO requirement, copper-cap and flatness requirements, and any customer-specific conditions. “Via-in-pad” or “filled via” alone is normally insufficient to define the finished structure. 6. Conclusion Via-in-pad is first a design method for solving high-density layout and routing constraints. In some applications, it can also shorten electrical paths or improve heat transfer. Once a via is placed in a component pad, however, the same location becomes both an interlayer connection and a soldering interface, and its manufacturing requirements change accordingly. Solder mask plugging has legitimate uses for ordinary vias, but it should not replace the structural filling, planarisation and continuous copper coverage required for a solderable via-in-pad. For many mechanically drilled BGA and QFN via-in-pad applications, VIPPO provides the more complete manufacturing solution. Not every via-in-pad requires VIPPO. The choice should depend on soldering, thermal, via-structure, cost and reliability requirements. Where the design requires a stable, flat and continuously solderable via-in-pad surface, VIPPO is generally the more complete approach. Final acceptance should therefore ask more than whether the hole has been filled. Is the copper cap thick enough? Is the pad sufficiently flat? Is the copper continuous? Is filling material exposed? If separation exists, at which interface does it occur? Connecting the design purpose, manufacturing method and acceptance criteria is what allows via-in-pad to save space without sacrificing assembly reliability. Reference Standards IPC-4761 Design Guide for Protection of Printed Board Via Structures About the Author Tony Niu is a PCB manufacturer with 25 years of hands-on industry experience. He shares practical manufacturing knowledge to help PCB designers and engineers understand how design decisions affect manufacturability, assembly and long-term reliability. His work covers engineering review, DFM, prototype and volume production, and complex PCB structures at SQPCB. Further information is available at: |
| Go back to Contents |
|
1. Introduction The Ultra-Thin Gold (UTG) finish was originally developed and perfected for production in 1995 to serve the stringent requirements of the watch PCB industry. Spearheaded by a team of chemists and chemical engineers with decades of PCB manufacturing experience, the objective was to engineer a surface finish superior to standard Electroless Nickel Immersion Gold (ENIG). Following continuous refinement through the early 2000s, UTG successfully supplied over 100 million zero-defect PCBs for the European and Indian watch industries. Since 2010, the technology has been scaled for the automotive sector, supplying approximately 4 million PCBs annually to leading automotive manufacturers for critical modules, including steering columns, mirrors, and wiper controls. The Ultra-Thin Gold (UTG) finish was originally developed and perfected for production in 1995 to serve the stringent requirements of the watch PCB industry. Spearheaded by a team of chemists and chemical engineers with decades of PCB manufacturing experience, the objective was to engineer a surface finish superior to standard Electroless Nickel Immersion Gold (ENIG). Following continuous refinement through the early 2000s, UTG successfully supplied over 100 million zero-defect PCBs for the European and Indian watch industries. Since 2010, the technology has been scaled for the automotive sector, supplying approximately 4 million PCBs annually to leading automotive manufacturers for critical modules, including steering columns, mirrors, and wiper controls. Recently presented and well-received at the IPC Expo, the UTG finish offers exceptional baseline metrics: • Solderability: Maintains robust performance under extreme stress with gold thicknesses as low as ≈ 5 nm. [1] 2. The UTG Process Architecture The UTG metallization sequence is an elegant pre-etch process: 1. Following standard panel plating a secondary imaging step covers the tracks, leaving only the solder/bond areas open for ultra-thin gold deposition. 2. The UTG process of nickel and gold plating is then followed by standard stripping and alkaline etching (UTG is not compatible with acid etchants). 3. Standard solder mask and post processing follows.
Image 1
Image 2
Image 3
Image 4
Image 5
Image 6
Image 7 The sequence L to R. 1-Imaging of panel plated copper, 2-Nickel plating of pattern, 3-Secondary imaging, 4-UTG gold plating, 5-Stripping, 6-Etching, 7-Solder masking. 3. Ecological Impact and Process Efficiency UTG fundamentally alters the thermodynamic and ecological footprint of HDI PCB manufacturing by eliminating costly ENIG chemistry. • 90% Gold Reduction: Mining and refining gold is one of the world's most carbon- and water-intensive metallurgical processes. By shifting from the IPC-4552B standard of 100 nm for ENIG to just 5 to 10 nm for UTG, the process eradicates 90% of the upstream carbon emissions and ecological degradation associated with the PCB precious metal supply chain. • Elimination of Hazardous MTO Dumping: Electroless nickel-phosphorus is chemically self-limiting; as reaction byproducts accumulate, the bath expires after a specific number of Metal Turnovers (MTO). This forces fabricators to regularly dispose of massive volumes of highly toxic, heavy-metal effluent. UTG utilizes pure electroplated nickel—a thermodynamically stable process that operates continuously, eliminating these hazardous waste cycles. • Thermal Energy Reduction: Conventional ENIG lines require continuous, massive electrical loads to maintain autocatalytic baths at 80°C, UTG replaces this thermal overhead with highly efficient electroplating 45°C, permanently slashing Scope 1 energy footprints on the factory floor. • Cycle Time Compression & Cellular Flow: Where ENIG requires prolonged dwell times of up to 30 mins in batch-processing baskets, UTG deposits 1.5 to 3 µ of pure nickel in just 5 to 10 mins respectively, and a 10 nm gold flash in 20 seconds. This rapid tact time eliminates Work-In-Progress (WIP) bottlenecks, enabling agile, single-panel cellular manufacturing that integrates seamlessly into automated Industry 4.0 architectures.
Unified Dual-Finish Architecture For modern automotive tactile cabin controls, standard manufacturing relies on complex post-etch masking, secondary plating operations, and parasitic bus bars to apply hard gold to specific switch contacts while using ENIG or OSP on solderable pads. This complicates board layout and introduces registration errors. Eliminating Via-Fill Liabilities Unlike post-mask finishes (ENIG) that require costly epoxy via-plugging to prevent chemical entrapment and hidden corrosion, UTG is a pre-etch plating. Vias are plated with pure nickel, etched, and solder-masked safely. The vias are never exposed to aggressive chemical treatments post-etch, entirely eliminating the dependency on via-plugging steps. Nanoscale Surface Integrity FESEM / AFM Analysis Further structural investigation using Field Emission Scanning Electron Microscopy (FESEM) and Atomic Force Microscopy (AFM) reveals that UTG produces a highly dense finish with zero grain boundary weaknesses and an exceptionally low Rq. While ENEPIG structures often exhibit distinct hemispherical NiP nodules and palladium micro-cracking, UTG images display a continuous, blemish-free topography. AFM data confirms that a mere 0.5µ nickel UTG plate is sufficient to reduce the Rq of plated copper from 200nm down to 9 nm.
The 2 images below are Ultra-thin gold, they show no nodules/grain boundaries.
3D Sidewall Anchoring (UTG + OSP) A historical concern regarding etched finishes on Non-Solder-Mask-Defined (NSMD) pads has been the exposed vertical copper sidewall (though permitted by IPC, MIL, and aerospace standards). To match the mechanical anchoring strength of ENEPIG—which wastes up to 50% of its precious metal budget plating the vertical walls—the UTG hybrid process incorporates OSP. Following the etch and solder-mask steps, the exposed vertical copper sidewalls are passivated with OSP. During reflow, the OSP volatilizes cleanly, allowing liquid solder to wet both the UTG-plated top and the pristine copper sidewalls. This creates the exact same 3D mechanical wraparound anchor as ENEPIG, maintaining maximum drop-shock reliability while permanently stripping out the 90% precious metal waste. The image is taken from a UTG plated BGA pattern, with solder paste print and BGA reflowed in a regular cycle. The BGA was removed in a re-balling station.
![]() ![]() 5. High-Frequency RF Compatibility As HDI PCBs scale to accommodate mmWave and AI substrates, insertion loss becomes the critical metric. Empirical testing at the Rogers Innovation Centre (Suzhou) evaluated UTG microstrips utilizing 0.5 µ and 3 ≥ nickel thicknesses with 5 to 10 nm gold on RO 1200, 5 mil laminate.
The empirical data demonstrates that the ultra-smooth topographical profile of UTG (Rq = 9 nm) and the chemical stability that allows RF microstrips to remain uncovered by dielectric solder mask provides a distinct signal integrity advantage. Above 10 GHz, UTG minimizes insertion loss compared to solder-mask-covered copper microstrips, and significantly outperforms standard High-Volume Manufactured (HVM) trapezoidal traces finished with chemical ENIG, making it a premier choice for high-frequency architectures.
For over two decades, ENIG and ENEPIG have served as the foundational surface finishes for the global high-reliability electronics industry. Their development was instrumental in enabling the transition to ultra-dense surface-mount technology, complex wire-bonded packages, and robust interconnects. The PCB industry owes much of its current miniaturization capabilities to the chemical engineering behind these legacy autocatalytic processes. However, as the industry crosses the threshold into 6G, AI-driven IC substrates, and mmWave frequencies—while simultaneously facing soaring cost of Gold and unprecedented global mandates for ecological sustainability and decarbonization—the physical and chemical limits of electroless nickel-phosphorus are being reached. Skin-effect attenuation, phosphorus embrittlement, and the massive carbon footprint of heavy gold consumption can no longer be ignored. Editors Note: UTG is potentially a game changer for environmental and cost conscious manufacturing of volume PCB's. The author would welcome contact and will manufacture samples for further research and assessment. Contact: Anil Kher, Managing Director, Micro Interconexion Pvt. Ltd. at
|
||||||||||||
| Go back to Contents |
|
1. Introduction As electronic devices become more powerful, designers are increasingly faced with the challenge of managing higher currents, greater heat generation, and demanding operating environments. While standard printed circuit boards (PCBs) are suitable for most consumer electronics, applications such as power supplies, industrial equipment, automotive electronics, aerospace systems, and renewable energy often require something more robust. This is where heavy copper PCBs come into play. Heavy copper PCBs are specifically designed to handle significantly higher electrical and thermal loads than conventional circuit boards. By using thicker copper layers, these boards deliver improved current carrying capacity, enhanced heat dissipation, and superior mechanical reliability. In this guide, we'll explain what heavy copper PCBs are, how they differ from standard PCBs, their benefits, design considerations, manufacturing challenges, and the applications where they excel.
2. What Is a Heavy Copper PCB? A heavy copper PCB is a printed circuit board that uses copper layers of 3 oz/ft² (approximately 105 μm) or greater on one or more layers. Standard PCBs typically use copper weights between*1 oz and 2 oz. Heavy copper PCBs are substantially thicker and capable of handling high-power applications.
Some specialist manufacturers can produce boards with copper thicknesses well beyond 10 oz for extremely demanding power applications. 3. Why Use Heavy Copper Instead of Standard Copper? The primary advantage of thicker copper is its ability to carry more electrical current without overheating. In many PCB designs, increasing trace width alone is enough to handle additional current. However, space constraints often limit how wide traces can become. Using heavier copper allows designers to increase current capacity without dramatically increasing trace width, and therefore the board size. The thicker conductor also reduces electrical resistance, leading to lower voltage drop and improved power efficiency. Another major benefit is thermal management. Copper is an excellent conductor of heat, so thicker copper layers spread heat more effectively across the PCB. This helps reduce hot spots, improves component reliability, and extends product lifespan.
4.1 Higher Current Carrying Capacity The combination of wider traces and increased copper thickness enables engineers to design compact power circuits without sacrificing electrical performance. 4.2 Improved Heat Dissipation This improved thermal performance reduces operating temperatures and allows components to perform more reliably under continuous heavy loads. 4.3 Better Mechanical Strength This makes heavy copper PCBs especially valuable in harsh operating environments, such as downhole tools. 4.4 Greater Reliability 4.5 Trace Width and Spacing 4.6 Larger Vias 4.7 Increased Solder Mask Thickness 4.8 Layer Stack-Up 5. Manufacturing Challenges Producing heavy copper PCBs is considerably more complex than manufacturing standard boards. An increase in copper thickness often requires a change in the PCB design. With a higher copper weight manufacturing boards with tight gaps and tracks can become extremely challenging. Producing heavy copper PCBs can sometimes require a consideration of those limitations at the design stage. The thicker copper requires longer etching times, increasing the risk of undercutting and reducing the minimum achievable trace size. Plating processes must also be carefully controlled to maintain consistent copper thickness throughout the board. Lamination becomes more demanding as copper thickness increases, and drilling through thick copper layers places greater wear on tooling. Thick copper features create larger differences in surface height on the board, making it harder for the prepreg resin to fill the spaces between tracks and bond the PCB layers together without defects. These factors increase manufacturing complexity, production time, and overall cost. 6. Heavy Copper in Flexible PCBs Heavy copper is not limited to rigid PCBs. It is also used in flexible and rigid-flex circuit boards for specialised high-power applications. In flexible PCBs, however, copper weight has a direct impact on flexibility. As copper thickness increases, the circuit becomes stiffer and less capable of repeated bending. While copper weights of 2 oz or greater are generally considered heavy for flex circuits, designers must carefully balance electrical performance against mechanical flexibility. To maximise reliability, flexible PCB designers often use the thinnest copper that still satisfies current requirements. In applications where heavy copper is unavoidable, bend areas may need to be redesigned or reinforced to reduce mechanical stress. 7. Common Applications Heavy copper PCBs are found in industries where reliability and high-power operation are essential. Typical applications include:
8. Is a Heavy Copper PCB Right for Your Project? Heavy copper PCBs offer clear performance advantages, but they are not always the best choice. Standard 1 oz or 2 oz copper is sufficient for most consumer electronics and low-power digital circuits. Heavy copper becomes the preferred solution when a design must carry high currents, withstand elevated temperatures, improve heat dissipation, or operate reliably in demanding industrial environments. Although manufacturing costs are higher, the improved reliability, reduced thermal stress, and longer operational life often outweigh the additional expense. Further information is available from ZOT Engineering at www.zot.co.uk. |
| Go back to Contents |
Section 6Universal High-Resolution Copper Patterning on Diverse Substrates via Sequential Laser-Induced Transfer and Electroless PlatingYaqiang Ji, Juexuan Xu, Weibin Yin, Yuhao Huang, Ru Pan and Yiming Chen
AbstractProducing fine copper tracks with good adhesion and mechanical durability remains a challenge in flexible electronics. This paper describes a new metallisation process combining two laser-transfer techniques with electroless copper plating. The first laser process creates a layer of copper particles, which the second process transfers and embeds into the surface of the chosen substrate. Electroless plating then builds up these particles into continuous conductive copper tracks. The process produces tracks as narrow as 20 µm, with electrical resistivity of around 2.0 × 10⁻⁸ Ω·m, close to that of bulk copper. The embedded particles provide strong adhesion, while the resulting tracks maintain good electrical performance after 8,000 bending cycles at radii of 3–6 mm. The technique has been demonstrated on a variety of materials, including polyimide, wood, fabric and paper. It offers a promising method for producing reliable copper circuits on flexible and unconventional substrates.
1. IntroductionThe growing use of flexible electronics in wearable devices, robotics and sensing applications has increased demand for fine copper conductors that combine high electrical conductivity with good adhesion and resistance to repeated bending. Copper is particularly attractive because of its excellent conductivity and relatively low cost, but producing reliable copper patterns on flexible and unconventional substrates remains a challenge. Conventional manufacturing methods include photolithography, screen printing, inkjet printing and electroless copper plating (ECP). Photolithography offers high resolution but involves complex processing and is poorly suited to rough or porous materials. Printing methods often require conductive inks and high-temperature curing, while traditional electroless plating generally depends on pre-patterned catalysts. In addition, copper coatings can crack or separate from flexible substrates during repeated bending. Laser direct writing (LDW) offers an alternative, allowing patterns to be produced without masks or physical contact. However, direct laser processing can damage heat-sensitive materials, and achieving both fine resolution and strong adhesion remains difficult. This study investigates a two-stage laser-transfer process followed by electroless copper plating. Laser-induced backward transfer (LIBT) first deposits copper particles onto a glass donor surface. Laser-induced forward transfer (LIFT) then transfers these particles onto the target substrate, where they become partially embedded and form catalytic sites for subsequent electroless plating. By separating the initial laser processing from the final substrate, the method reduces thermal damage while improving copper adhesion through mechanical interlocking. It provides a potential route to producing fine, durable copper circuits on materials including polyimide, wood, fabric and paper.
2. Materials and Methods2.1. Experimental MaterialsThe experiments used 125 µm polyethylene terephthalate (PET) film, polyimide (PI), glass, wood, fabric and paper substrates. Glass slides served as donor substrates for the laser-transfer process. The electroless copper plating solution was prepared using analytical-grade chemicals, including copper sulphate, sodium hydroxide, potassium sodium tartrate, EDTA and formaldehyde. Deionised water was used throughout. 2.2. Sequential Two-Step Laser TransferThe process employed a 355 nm picosecond laser to carry out two successive transfer operations. Laser-induced backward transfer (LIBT): Copper particles were deposited onto a glass donor substrate using a laser power of 2 W, scanning speed of 1,000 mm/s and repetition rate of 40 kHz. This produced a relatively uniform copper particle layer for subsequent transfer. Laser-induced forward transfer (LIFT): The glass donor and receiving substrate were positioned approximately 100 µm apart. A second laser operation, using 0.6 W power, 800 mm/s scanning speed and 400 kHz repetition rate, propelled the copper particles onto the receiving surface. The transferred particles became partially embedded in the substrate, creating a firmly anchored catalytic seed layer for subsequent electroless copper deposition. 2.3. Electroless Copper PlatingFollowing laser transfer, the substrates were rinsed with deionised water to remove loose particles. Electroless copper plating was carried out at 50°C using a freshly prepared solution containing copper sulphate, sodium hydroxide, EDTA, potassium sodium tartrate and formaldehyde. For PET substrates, a deposition time of approximately 3–5 minutes produced a continuous copper film. The samples were then rinsed to remove residual plating chemicals. 2.4. Characterisation and TestingThe deposited copper patterns were examined using scanning electron microscopy (SEM) to assess surface morphology and microstructure, while X-ray diffraction (XRD) was used to investigate crystal structure. Electrical resistance was measured using a four-probe method. Adhesion was assessed using a cross-hatch tape test, and mechanical durability was evaluated through repeated bending while monitoring changes in electrical resistance. 3.1. Copper Pattern FormationFigure 1 illustrates the two-stage laser-transfer process followed by electroless copper plating (ECP). During laser-induced backward transfer (LIBT), laser energy releases copper particles from the original copper surface, depositing them onto a glass donor substrate. The resulting particle layer provides the material for the second transfer stage. Laser-induced forward transfer (LIFT) then propels these particles from the glass donor onto the receiving substrate. The particles become partially embedded in the surface, forming a mechanically anchored catalytic seed layer. Subsequent electroless plating builds up the deposited copper until the individual particles merge into continuous conductive tracks. Separating the two laser operations reduces direct thermal exposure of the receiving material, allowing copper patterns to be produced on heat-sensitive and unconventional substrates. Successful metallisation was demonstrated on polyimide, wood, fabric and paper.
Figure 1. Two-stage laser-transfer process followed by electroless copper plating. 3.2. Microstructure and Copper DepositionScanning electron microscopy (SEM) was used to examine the copper at each processing stage (Figure 2). Following LIBT, a relatively uniform layer of copper particles was deposited onto the glass donor. After LIFT, the particles were distributed across the PET surface, with evidence of partial embedding into the polymer. This mechanical interlocking provides improved adhesion and helps stabilise the catalytic seed layer during plating. Electroless deposition caused the individual copper particles to grow and join together, producing a continuous metallic film. X-ray diffraction confirmed the formation of crystalline copper, while contact-angle measurements indicated improved surface wettability following laser treatment. Figure 3 illustrates the change in surface morphology during plating. Initially, the transferred seed layer consisted of discrete copper particles. As deposition progressed, copper filled the spaces between the particles, eventually forming a dense, continuous conductive structure.
Figure 2. SEM examination of copper particles following LIBT and LIFT, the completed copper coating after electroless plating, X-ray diffraction results and surface wettability measurements. 3.3. Pattern ResolutionThe combined laser-transfer and plating process produced continuous copper tracks with an average minimum linewidth of approximately 20 µm on PET substrates (Figure 3). Pattern quality depended on laser power, scanning speed and the separation between donor and receiving substrates. Insufficient laser energy produced incomplete copper transfer, while excessive energy increased particle scattering, edge roughness and the risk of substrate damage. Similarly, excessive separation between the donor and receiver reduced pattern accuracy because of particle dispersion during transfer. Optimising these parameters produced well-defined copper tracks with consistent dimensions and relatively sharp edges.
Figure 3. Copper track morphology before and after electroless plating, including optical and SEM images demonstrating linewidths of approximately 20 µm. 3.4. Electrical Performance, Adhesion and Bending DurabilityThe electroless copper deposits exhibited electrical resistivity of approximately 2.0 × 10⁻⁸ Ω·m, close to the measured value of 1.8 × 10⁻⁸ Ω·m for commercial copper sheet (Figure 4a). Adhesion was evaluated using a cross-hatch tape test in accordance with ASTM D3359-23. The deposited copper achieved the highest classification, 5B, with no detectable coating removal. This strong adhesion is attributed to the laser-transfer process, which partially embeds copper particles into the polymer surface. The resulting mechanical interlocking helps prevent separation of the copper coating during deformation. Bending tests were conducted at radii between 3 and 6 mm, with electrical resistance monitored throughout. At bending radii of 4 mm and above, resistance remained essentially unchanged. Even at the more demanding 3 mm radius, the normalised resistance remained below 1.3 after 8,000 bending cycles. Subsequent microscopic examination confirmed that the copper tracks remained continuous, with no visible cracking or delamination in the inspected regions.
Figure 4. Electrical resistivity, cross-hatch adhesion testing and changes in electrical resistance during repeated bending at different radii.
4. ConclusionsThis study demonstrates a copper metallisation process combining two-stage laser transfer (LIBT and LIFT) with electroless copper plating. By separating the initial laser processing from the receiving substrate, the method reduces thermal exposure and enables fine copper patterns to be produced on materials including PET, polyimide, wood, fabric and paper. The process produced continuous copper tracks with linewidths of approximately 20 µm and electrical resistivity of 2.0 × 10⁻⁸ Ω·m, approaching that of bulk copper. Laser-induced embedding of copper particles provided excellent adhesion, while the completed conductors maintained good electrical performance after 8,000 bending cycles at radii of 3–6 mm. The successful demonstration of these electrodes in a flexible sensing device further illustrates the potential of this approach for manufacturing reliable copper circuits on a wide range of substrates.
Editor's note: This article is an edited and abridged version of “Universal High-Resolution Copper Patterning on Diverse Substrates via Sequential Laser-Induced Transfer and Electroless Plating” by Yaqiang Ji, Juexuan Xu, Weibin Yin, Yuhao Huang, Ru Pan and Yiming Chen, published in Micromachines, 2026, 17(4), 391. Original article: https://doi.org/10.3390/mi17040391 Reproduced and adapted under the Creative Commons Attribution 4.0 International (CC BY 4.0) licence. Changes include abridgement and editorial restructuring. Supplementary materials and the complete reference list are available with the original publication.
References: The complete reference list is available in the original published paper. Originally published in Micromachines, 2026, 17(4), 391. DOI: 10.3390/mi17040391. © 2026 the authors. Licensed under Creative Commons Attribution 4.0 (CC BY 4.0). This version has been abridged and edited for clarity and presentation in the ICT Journal. |
| Go back to Contents |
|
Section 7 John Burke |
|
A comprehensive e-book has been released by John Burke which covers updated procedures for pcb design and assembly.
Here is a snapshot of the first part of the index of contents.
The e-book is available here. Read more... |
| Go back to Contents |
|
In Remembrance of Steve Lloyd, Managing Director of GSPK Circuits Limited.
It is with profound sadness that GSPK Circuits announces the passing of our Managing Director, Steve Lloyd, who passed away peacefully in his sleep on Thursday, 1st October 2026, following a long battle with illness. Steve joined the GSPK Group in April 1995 as Senior Operations Manager with GSPK Electronics. Through his unwavering dedication, visionary leadership and deep commitment to the industry, he rose to become Managing Director of GSPK Circuits Limited, a role he held with exceptional professionalism and distinction. Over his remarkable three-decade tenure with the Group, Steve played an instrumental role in shaping the growth, success and values of our business. He was widely respected across the electronics manufacturing sector by customers, suppliers, industry partners for his expertise, tenacity and relentless pursuit of excellence. Beyond his professional accomplishments, Steve was a mentor, colleague and true friend to many. His leadership, guidance and warmth left an indelible mark on everyone who had the privilege of working with him. On behalf of the Board of Directors, executive leadership, and all employees at GSPK, we offer our deepest condolences to Steve’s family, friends, and loved ones during this difficult time. Steve’s legacy, service and memory will remain an integral part of GSPK Circuits. |
|
🎉 Celebrating 42 Incredible Years – Thank You, Chris Wall!
Congratulations to Chris Wall BSc(Hons), F.Inst.C.T. on his well-earned retirement after 42 years with Electra Polymers Ltd. As one of the company's founders, Chris has played an instrumental role in its development and success. His knowledge, dedication and commitment have helped shape Electra into the business it is today. Chris leaves behind a remarkable legacy and will be greatly missed by colleagues and friends throughout the industry. Thank you, Chris, and enjoy your retirement! 🍾🥂 |
|
Electra Polymers Announces New Leadership Appointments Electra Polymers has announced three senior management appointments as the company enters a new phase of development. Shaun Tibbals has been appointed Managing Director, Antony Earl becomes Technical Support & Compliance Director, and Ashley Steers takes up the position of Sales & Marketing Director. The appointments are intended to strengthen Electra's leadership team as the company continues to develop its specialist coatings technology, support customers and expand its international presence within the PCB industry. |
|
Jonathan Jones Promoted to Technical Manager at Merlin Circuit Technology Merlin Circuit Technology Ltd has promoted Jonathan Jones to Technical Manager in recognition of his technical expertise, leadership qualities and contribution to the business. The company praised Jonathan’s professionalism, his willingness to take on new responsibilities and the strong relationships he has developed with customers and colleagues. In his new role, Jonathan will lead Merlin’s technical function and drive ongoing improvements, helping the company maintain high standards of quality, service and technical performance. |
|
Gary Kerr Appointed General Manager of Zot’s PCB Division Zot Engineering has promoted Gary Kerr to General Manager of its PCB Division. Having progressed from an apprenticeship to divisional leadership, Gary brings extensive experience of the business to his new role. The company marked his appointment with an interview exploring his career, values and plans for the division’s growth. |
| Go back to Contents |
|
Accutech PCB Inner-Layer Registration and Bonding ADEON Technologies has announced the arrival in Europe of the first Accutech dual-table bonding system, which is being prepared for delivery to a European PCB manufacturer. The equipment is designed for inner-layer registration and bonding prior to multilayer pressing. Available configurations include pin and optical registration, electromagnetic heat fusion technology, and 12 upper and 12 lower welding heads. Read more... |
|
A-Gas Highlights Advanced Copper Plating Processes for HDI Manufacturing A-Gas Electronic Materials has highlighted two specialist acid copper plating processes from Qnity, formerly DuPont, aimed at demanding PCB manufacturing applications. Microfill EVF-III is designed to provide effective panel via filling while maintaining good throwing power in plated through-holes. Microfill AHF is intended for high-aspect-ratio through-hole filling, addressing the increasingly demanding requirements of high-density interconnect (HDI) boards and IC substrates. Both processes form part of the specialist plating chemistry portfolio offered by A-Gas Electronic Materials, supporting manufacturers working with increasingly complex interconnection structures. Read more... |
|
Amphenol Trackwise Explores Flexible PCB Interconnects for Spacecraft Solar Arrays Amphenol Trackwise Designs has published a new technical whitepaper examining the use of long-length flexible printed circuits as an alternative to conventional wiring harnesses in deployable spacecraft solar arrays. As spacecraft power requirements increase, larger and more complex solar arrays must operate within strict constraints on mass, stowed volume and electrical reliability. Long flexible printed circuits offer the possibility of integrating multiple conductors into a single continuous interconnect, reducing weight, component count, connector interfaces and assembly complexity. The whitepaper, Long Flex PCB Interconnects for Deployable Spacecraft Solar Arrays, examines the electrical, mechanical and manufacturing advantages of this approach, including controlled impedance, integrated shielding, engineered bend regions and repeatable manufacturing processes. For folding and roll-out solar arrays, these flexible interconnects could become an integral part of the deployable structure, rather than simply providing connections between individual components. The whitepaper is available to read and download from the Trackwise website. Read more... |
|
CCI Eurolam Qualifies New EMC Manufacturing Facility in Malaysia CCI Eurolam has completed a qualification audit of Elite Material Co.'s (EMC) new high-technology manufacturing facility in Penang, Malaysia, strengthening its supply arrangements for PCB laminate materials. The audit highlighted the plant's advanced factory automation, process control and quality management systems. EMC is expanding its manufacturing capacity in response to increasing demand for high-performance PCB materials, particularly from artificial intelligence infrastructure and advanced electronics applications. CCI Eurolam says the additional capacity will help improve supply-chain resilience and support the growing requirements of European PCB manufacturers. The company is also continuing to invest in its European operations, including further expansion of prepreg and laminate panel-processing capacity at its new 8,000 m² facility in Düren, Germany. Read more... |
|
EuroTech Expands UK PCB Manufacturing Capabilities The EuroTech Group has announced significant investment in its PCB manufacturing facility in Exmouth, Devon, strengthening its capacity to meet growing demand for complex printed circuit boards. Over the past 18 months, the company has recruited 25 additional employees and invested in new manufacturing equipment, including drilling machines, alongside improvements to factory organisation and production efficiency. These developments are expanding EuroTech's capabilities in rigid, flexible and flex-rigid PCB manufacturing, enabling the company to support an increasingly diverse range of technically demanding applications. EuroTech reports a 36% increase in turnover during its latest financial year, contributing to a strong forward order book. The company is continuing to invest in equipment, training and manufacturing processes to increase throughput and reduce lead times. Read more... |
|
Exception PCB Highlights Importance of UK Manufacturing for Sovereign Capability Exception PCB has highlighted the strategic importance of domestic printed circuit board manufacturing in supporting the UK's defence, aerospace and other critical technology sectors. In a recent article, the Tewkesbury-based manufacturer argues that increasing geopolitical uncertainty, supply-chain disruption and concerns over sensitive design data are encouraging companies to reassess their reliance on overseas PCB suppliers. UK-based manufacturing offers advantages including shorter and more predictable lead times, closer engineering collaboration, improved traceability and greater control over production quality. These benefits are particularly important for long-term programmes in defence, aerospace, medical technology and secure communications. Exception PCB also emphasises the importance of maintaining domestic manufacturing expertise and investing in advanced PCB production capabilities to strengthen the resilience of the wider UK electronics industry. Read more... |
|
Garner Osborne Expands UK PCB Manufacturing Capacity Garner Osborne Circuits is expanding its manufacturing operations in Newbury as part of an investment and recruitment programme across the Agile Circuit Technology Group. The Group, which also includes Active-PCB Solutions in Reading, is recruiting additional production and management personnel to support increasing demand for UK-based PCB manufacturing and electronics assembly services. Recent investments across the Group include additional manufacturing equipment, expanded reflow and conformal coating capabilities, and improvements to production software and operational systems. Garner Osborne has also strengthened its production planning and night-shift capacity, enabling three-day turnaround on qualifying bare PCB orders. The developments form part of the Group's strategy to increase manufacturing capacity while maintaining quality, flexibility and customer support across its UK operations. Read more... |
|
Graphic PLC Highlights Early Design-for-Manufacture Collaboration Graphic PLC has highlighted the importance of early applications engineering involvement in improving printed circuit board manufacturability, reliability and production efficiency. In a recent technical article, the Crediton-based PCB manufacturer explains how collaboration during product development can help optimise material selection, board construction, manufacturing specifications and compliance requirements before designs are finalised. Graphic identifies three stages at which applications engineering can contribute: initial product development, design data finalisation and late-stage manufacturing review. The company emphasises that early involvement offers the greatest opportunity to improve reliability, reduce manufacturing risk and control costs and lead times. The company warns that leaving design-for-manufacture reviews until after quotation or order placement can result in avoidable changes, production delays and increased costs. Read more...
|
|
GSPK Circuits Achieves ISO 14001 Environmental Certification GSPK Circuits, the Boroughbridge-based PCB manufacturer, has achieved ISO 14001:2015 certification for its Environmental Management System, demonstrating its commitment to reducing the environmental impact of its manufacturing operations. The certification provides a structured framework for managing environmental responsibilities, improving resource efficiency and supporting continual improvement. The achievement follows the company's investment in renewable energy, including an on-site solar installation designed to reduce its reliance on grid electricity. ISO 14001 adds to GSPK's existing range of quality and industry accreditations, reinforcing its commitment to responsible UK printed circuit board manufacturing. Read more... |
|
ICAPE Group Introduces European-Manufactured Flexible PCB Jumpers ICAPE Group has expanded its range of high-reliability interconnection products with the introduction of C-FLEX Jumpers, manufactured by its MMAB facility in Malmö, Sweden. Designed as an alternative to conventional wiring harnesses and connectors, C-FLEX consists of parallel copper conductors laminated between polyimide insulation layers, providing a lightweight, low-profile interconnection between printed circuit boards. The jumpers are available in standard conductor pitches of 1.27 mm and 2.54 mm, with a nominal overall thickness of 0.25 mm. They offer resistance to vibration and thermal cycling, with an operating temperature range of −55°C to +105°C. Customisation options include conductor dimensions, length, termination geometry and surface finish, with ENIG and bright tin available. Applications include aerospace, defence, railway systems and industrial automation. Manufacture at ICAPE's Swedish facility provides European production capability, material traceability and engineering support for demanding electronic assemblies. Read more... |
|
Jiva Materials Wins International Climate Technology Award Jiva Materials has won the Climate Tech & Environmental Protection category at the 2026 Hello Tomorrow Global Challenge, recognising the company's development of its recyclable Soluboard® printed circuit board substrate. The Hampshire-based company was selected from more than 4,800 start-up applicants worldwide, progressing through a shortlist of 100 finalists before receiving the category award at the Hello Tomorrow Global Summit in Amsterdam. Soluboard® replaces conventional glass-fibre and epoxy PCB substrate materials with a naturally derived alternative designed to facilitate the recovery of copper and electronic components at the end of a product's life. The award comes as Jiva continues to develop the commercial potential of Soluboard®. The company has also reported achieving UL 94 V-0 flammability classification, an important milestone for applications requiring more demanding fire-performance standards. The recognition highlights growing international interest in alternative PCB materials and technologies designed to reduce electronic waste. Read more... |
|
MacDermid Alpha Advances Metallisation Technologies for Next-Generation PCBs MacDermid Alpha Electronics Solutions has highlighted developments in advanced metallisation technologies for high-density interconnect (HDI) printed circuit boards and IC substrates. At the IMPACT Conference and TPCA Show 2026 in Taipei, the company presented research covering periodic pulse reverse (PPR) copper plating, advanced via filling, final finishes and through-glass via metallisation. These technologies address manufacturing challenges associated with artificial intelligence and high-performance computing, where increasing interconnect densities and finer circuit features demand greater control of copper distribution and plating uniformity. Featured processes included PC 710 for improved copper thickness uniformity and throwing power, MacuSpec™ VF-TH 500 and AVF 700 for advanced via filling, and Shadow® Plus graphite-based direct metallisation as an alternative to conventional electroless copper processing. Read more... |
|
Merlin Circuit Technology - ISO 14001 recertification Merlin Circuit Technology has successfully renewed its ISO 14001 certification for environmental management. The company says the achievement reflects continuing work on environmental controls, waste reduction and sustainability throughout its manufacturing operations. Its environmental management arrangements support more efficient use of resources and efforts to reduce the impact of production. Merlin described the recertification as recognition of the work its team puts into maintaining environmental standards and improving manufacturing practices. The announcement does not specify individual projects or quantified reductions in waste or energy use. Read more |
|
Merlin Flex - Further investment in long flexible circuits Merlin Circuit Technology has successfully renewed its ISO 14001 certification for environmental management. The company says the achievement reflects continuing work on environmental controls, waste reduction and sustainability throughout its manufacturing operations. Its environmental management arrangements support more efficient use of resources and efforts to reduce the impact of production. Merlin described the recertification as recognition of the work its team puts into maintaining environmental standards and improving manufacturing practices. The announcement does not specify individual projects or quantified reductions in waste or energy use. Read more |
|
Newbury Electronics Ltd celebrates 70 years
In 2026, Newbury Electronics Ltd celebrates 70 years in business — a milestone that reflects the experience, capability and long-term relationships behind everything we do Read more... |
|
Schmoll Integrates Microscope into Laser Drilling Machines Schmoll Maschinen has integrated a microscope into selected laser drilling machines, allowing operators to inspect the first holes of a production batch without removing the panel or disturbing its alignment. The microscope also supports initial process setup. Operators can examine test structures directly on the machine and adjust parameters such as pulse energy, pulse count and focus position before further fine-tuning. Schmoll says the facility shortens setup times, reduces test runs and material waste, and helps operators confirm process quality before starting volume production. Read more... |
|
Strip Tinning Awarded £3 Million Grant to Expand UK Manufacturing Strip Tinning Holdings has been awarded a £3 million grant under the Government’s DRIVE35 programme to support the expansion of its UK manufacturing capabilities. The funding will help the company develop specialist skills and scale production of its Cell Contacting System (CCS) technology for international customers. Combined with its own investment, the grant is intended to support demand from existing contracts in 2027 and beyond. In September, Strip Tinning confirmed that first-stage conditions had been met and a grant offer letter signed with Innovate UK, allowing £600,000 of project expenditure while second-stage approval was completed. |
|
Sun Chemical Highlights Advances in Electronic Materials Sun Chemical has announced developments in its SunTronic and SunSens electronic materials portfolios, covering applications in automotive, healthcare, sensors and wearable devices. The expanded SunTronic range includes silver conductive inks with increased recycled content, alongside formulations with lower silver content. Further developments include high-resolution conductive inks, LED-curable dielectrics and updated materials for stretchable and wearable electronics. The developments formed part of Sun Chemical’s announcement ahead of TechBlick’s *The Future of Electronics Reshaped* event in Berlin on 21–22 October 2026. Read more... |
|
Ventec & MICAM join forces for Mission-Critical CCL production Ventec and MICAM to establish joint venture for European production of mission-critical copper-clad laminates in Ireland. New facility will strengthen sovereign European supply of materials for defence-grade electronics. Ventec International Group (TWSE: 6672), a Taiwanese specialist manufacturer of copper-clad laminates (CCL) and prepregs (PP) serving a global customer base, and MICAM a long-established manufacturer of advanced composites to the industrial, security and defence industries are developing a joint venture to establish copper-clad laminate production at MICAM’s manufacturing facility in Mallow, Ireland. |
|
Zot Improves Solder-Mask Production with Direct Imaging Zot Engineering has reported improvements in solder-mask production following the installation of a Schmoll maskless direct imaging system. The system has virtually eliminated reprocessing caused by solder-mask misalignment, while removing the need for photographic films and their associated production costs. Improved registration accuracy has also enabled Zot to undertake PCB projects with finer features and tighter tolerances. The company says solder-mask imaging is no longer a production bottleneck, helping improve workflow and reduce customer lead times. Primarily used for solder mask, the system can also provide backup for other imaging processes. Read more... |
| Go back to Contents |
| Section 10 | Corporate Members of the ICT | |
| Adeon Technologies BV | ![]() |
adeon.nl |
| A-Gas Electronic Materials | ![]() |
agasem.com |
| Amphenol Invotec Ltd | ![]() |
amphenol invotec.com |
| Amphenol Trackwise Designs Ltd | trackwise.co.uk | |
| Atotech UK Ltd. | ![]() |
atotech.com |
| CCI Eurolam | ![]() |
cci eurolam.com |
| Electra Polymers Ltd | ![]() |
electra polymers.com |
| Eurotech Group | ![]() |
eurotech-group |
| Exception PCB Solutions | ![]() |
exception pcb.com |
| Garner Osborne | ![]() |
garner osborne.co.uk |
| Graphic plc | ![]() |
graphic.plc.uk |
| GSPK (TCL Group) | ![]() |
gspk circuits.ltd.uk |
| Holders Technology UK | ![]() |
holders technology.com |
| Icape Group | ![]() |
icape-group.com |
| Jiva Materials | ![]() |
jivamaterials.com |
| Macdermid Alpha | ![]() |
macdermid alpha.com |
| Merlin Circuit Technology Ltd | ![]() |
merlin pcbgroup.com |
| Merlin Flex Ltd | ![]() |
merlinflex.com |
| Newbury Electronics Ltd | ![]() |
newbury electronics.co.uk |
| Pillarhouse Int | ![]() |
pillarhouse.co.uk |
| Polar Instruments | polar instruments.com | |
| Schmoll Maschinen | ![]() |
schmoll-maschinen.de |
| Strip Tinning Ltd | ![]() |
striptinning.com |
| Sun Chemical Corp | sunchemical.com | |
| Teledyne Labtech | ![]() |
teledyne labtech.com |
| Ventec Europe | ![]() |
ventec- europe.com |
| Zot Engineering Ltd | ![]() |
zot.co.uk |
| Go back to Contents |
|
Section 11 |
ICT Council Members |
|
Council Members |
Steve Driver (Chair), Alun Morgan (Technical Director, Hon Sec, & Events), Chris Wall (Treasurer), Leigh Allinson (Vice-Chair), Richard Wood-Roe (Journal Editor & Web Site), Brian Morgan (Membership Secretary), Mat Beadel, Neil Chamberlain, Emma Hudson, Pete Starkey, Francesca Stern. |
|
Section 12 |
Editor's NotesThe ICT Journal |
|
Richard Wood-Roe |
Instructions / Hints for Contributors We really look forward to any input you have. Technical papers, company news, personal news, industry comments or observations. As it is a digital format the length is not an issue. Short is better than none at all! I really do look forward to receiving articles for publication. Richard Wood-Roe |
| Go back to Contents |


Alun Morgan
Figure 1. Why via-in-pad is needed: A conventional structure uses separate locations for the pad, trace and via; via-in-pad places the via inside the pad to save routing space in high-density component areas. The lower photographs show practical via-in-pad features within component footprints.
Figure 2. Structural comparison of four via-in-pad treatments. An open via, solder mask plugging, resin filling and VIPPO do not provide the same solderable surface or reliability.
Figure 3. Typical VIPPO manufacturing process. Resin filling, curing, planarisation and copper cap plating work together to create a flat, continuous and solderable pad surface.
Figure 4. VIPPO structure and key inspection locations. Copper-cap voids, exposed fill material and separation at different interfaces must be evaluated separately.


















































